The “Chamfer” tool creates various chamfers in different objects.
The added material object created employing this tool is of a specific
type, thus it is recommended to be applied in case a detailed chamfer statement
or chamfer marking is required, with paying attention to the particularities
of dimensions of the chamfers. In practice, these are exceedingly rare
requirements. In all other cases use standard cut-off tools described above.
The edge preparation is necessary for setting weld-outs. In older
TS versions the “Weld” tool was not able to exercise edge preparation.
In the current versions, edge preparation is customizable at the "Weld
seam Properties" dialog window.
Herein we will examine the “Chamfer” tool enabling edge preparation
This tool creates a chamfer along the line specified by two points.
Tekla Structures v21.1
Tekla Structures v2021
Create a beam of 500 mm length.
Tekla Structures v21.1
Tekla Structures v2021
Let’s create a chamfer along the line by using the following algorithm:
Make sure all operations are canceled or press the Esc key.
Enable the “Create chamfer- For part edge” tool.
Select the initial object for which a chamfer should be created.
Indicate the starting point of the chamfer.
Indicate the endpoint of the chamfer.
To disable the “Create chamfer- For part edge” tool, press
the Esc key.
Tekla Structures v21.1
Tekla Structures v2021
Chamfers are displayed as solid objects though it is subtended that there
is no beam body at their place. Select the chamfer you have created and
by a double click on it go to its "Properties" menu.
Into the “Name'' field you can write any substantial
information about the edge, such as the equipment type to cut the edge,
so far as it can be reflected in the drawings and statements.
Tekla Structures v21.1
Tekla Structures v2021
Let’s edit the values of X and Y parameters to bigger ones.
Tekla Structures v21.1
Tekla Structures v2021
When configuring the dimensions of a chamfer, keep in mind that these
are essential for preparing a part for welding. Chamfer dimensions and
their shape depend on the weldable parts thickness and the weld-seam type
to be applied. Each country has its regulations for creating chamfers,
thus consult relevant sources for regulatory guidelines with your country,
and never set up these values in a random way.
In the current case study, create a chamfer of 45 degrees angle with the
root face dimensions equal to 2 mm (marked by c in the picture above).
In this regard, open the "Beam Properties" window and find
out the I-beam flange thickness.
Tekla Structures v21.1
Tekla Structures v2021
Refer to the below picture and pay attention to the parameter framed with
red. The flange thickness value may vary, depending on the profile type
selected.
Tekla Structures v21.1
Tekla Structures v2021
From the above picture, you can see that the flange thickness value is
8 mm, thus 2 mm should be set aside for the root face, resulting in that
the chamfer dimensions should be as follows: 8 - 2=6 mm. Write in
this value into the respective field of the “Edge Chamfer Properties”
window.
Tekla Structures v21.1
Tekla Structures v2021
Create one more chamfer along the I-beam side in the counter direction
Tekla Structures v21.1
Tekla Structures v2021
The new chamfer is of the full I-beam side length.
Tekla Structures v21.1
Tekla Structures v2021
If a chamfer is to be of a definite length, it is required to configure
the “Chamfer ends” values to “Straight”, as it
is shown below:
Tekla Structures v21.1
Tekla Structures v2020
In practice, this chamfer type is of immense complexity thus partially
chamfer edge preparations are mostly avoided. However, it may
be required and chamfers are created by a specific tool with an entry angle
different from 90 degrees.
Switch the end type values, thus the distance fields will get activated.
These are increasing chamfers and allow the tool to perform an entry at
a more shallow angle.
Tekla Structures v21.1
Tekla Structures v2021
Select the chamfers and in the right-click menu press on “Hide”,
to temporarily hold them back from the view ( to remove/to hide, but not
to delete).
This tool is applicable only for steel plates and poly beam objects and
is not creating a new object type such as chamfer. It just applies the
properties set of a chamfer in a point to a group of points.
Tekla Structures v21.1
Tekla Structures v2021
Create a plate with dimensions of 200x200. Select one of its points
Configure the values of parameters as it is shown in the below picture
Tekla Structures v21.1
Tekla Structures v2021
The algorithm for using the “Create Chamfer - For part corner”
Make sure all operations are canceled or press the Esc key.
Select the initial object (plate).
Enable the “Create chamfer- For part corner” tool.
Select the point subject for applying the properties of the formerly created
chamfer.
If required, select other points.
To disable the “Create chamfer- For part corner” tool, press
the Esc key.
Tekla Structures v21.1
Tekla Structures v2021
Since creating chamfers is available by configuring the parameters of
the “Chamfer properties” dialog window, we would not recommend
you to use the “Create chamfer- For part corner” tool.
This tool is applicable only for steel plates and poly beam objects and
is not creating a new object type such as chamfer. It just applies the
properties set of a chamfer in a point to a group of points.
Tekla Structures v21.1
Tekla Structures v2021
Create a plate with dimensions of 200x200. Select one of its points
Configure the values of parameters as it is shown in the below picture
Tekla Structures v21.1
Tekla Structures v2021
The algorithm for using the “Create Chamfer - For part corner”
Make sure all operations are canceled or press the Esc key.
Select the initial object (plate).
Enable the “Create chamfer- For part corner” tool.
Select the point subject for applying the properties of the formerly created
chamfer.
If required, select other points.
To disable the “Create chamfer- For part corner” tool, press
the Esc key.
Tekla Structures v21.1
Tekla Structures v2021
Since creating chamfers is available by configuring the parameters of
the “Chamfer properties” dialog window, we would not recommend
you to use the “Create chamfer- For part corner” tool.